![](/static/66c60d9f/assets/icons/icon-96x96.png)
![](https://lemmy.world/pictrs/image/8286e071-7449-4413-a084-1eb5242e2cf4.png)
I don’t see why you think those are web based, usually people run this at home but glad you find what you are looking for
I don’t see why you think those are web based, usually people run this at home but glad you find what you are looking for
As far as photo librabry, you can compare the different solutions at https://github.com/meichthys/foss_photo_libraries
I have nvme setup on my pi 4 (I know it’s overkill for that purpose but already had pi setup like this prior to klipper), that being said I will definitely look at getting one with communication control even if power never goes down for more than a couple of seconds
If you make a search “ender 3 5v pin”, you will find plenty of examples on Reddit, octoprint forum and others. Problem was (or is) that printer was still getting power when OFF, it could lead to plenty of issues with worst case scenario where the mainboard died.
You definitely needs to calibrate your estep and flow rate as others mentioned. If numbers were correct then you might have a partial clog. If so, clean it and check Luke’s hotend fix on thingiverse/printable (really worth it). https://m.youtube.com/watch?v=7tCxO17XZtw
Under extrusion aside, you can get better text details by using a smaller nozzle as one issue for the text clarity is line width, while it isn’t ideal you can also try to set 0.30/0.35 line width with 0.4 nozzle.
Also, if you do plug in usb from your computer to printer (to calibrate estep), make sure to cover the 5v pin on usb cable with electrical tape. Otherwise you might wreck your printer mainboard. https://community.octoprint.org/t/put-tape-on-the-5v-pin-why-and-how/13574
Just adding to your comment that if OP goes that route, he will need to cover 5v pin with some electrical tape on usb otherwise he will wreck is printer board. (Unless recent ender 3 have this issue fixed but I doubt)
I will look for a fanless ups as I’m kinda sensitive to noise and everything is setup in my living room…, I will make sure I have the mute option available.
Shouldn’t be an issue, power outage here are mostly about one second (5 at max) and even if my printer is being halted, my glass bed stick so much that my print don’t pop off by themselves, I always use a scraper even when completely cool down.
Actually I could even run Klipper on mini pc but would need a very long usb to reach printer and thought it wasn’t ideal. As for the mini pc, I’m running proxmox but I’m far from being an expert so not sure if I can manage CPU scaling.
Should have added in my post that power outage don’t last more than a few seconds so ups should be fine
“why are they separated”, not sure what you meant, mini pc is acting as a server for a few usage and pi is dedicated to klipper.
Thanks
Yeah, I only care to keep the printer running for just a few seconds but thanks for the input
First time I heard of online usv (also English isn’t my main language), will have to check this out
Power outages are usually very short (few seconds max). Are fanless ups ok or should I stay away from it. The one I’m looking out at the moment is Eaton Ellipse eco 500
Didn’t think about noise and that’s important to me so thanks, is there anything special to look for the battery to make sure it can support my 3 devices at the same time? Like amp or other electric specifications?
Relying on 4 nvme drive for low power isn’t ideal as nvme drive needs about twice more power compare to sata SSD.
Don’t have the max version but I believe they shared the same extruder as cr6 se
This video shows how to put it back together https://www.youtube.com/watch?v=adVzvhmIKZM
And they are several option to replace extruder. Cheap one are the same compatible of ender 3 like this one at 4€ https://a.aliexpress.com/_EyXIa19 but you will have to print a raiser for the filament sensor
I’m not 100% sure but this might also depend which OS you are running on your pi. Did change from SD card to SSD few years back for my home assistant setup (now running with a mini pc) at the time I went for a geekpi adapter (can’t recall exact model).
Try a quick ducduck search “sata adapter #yourOS#” and see if a list come up. Here is one for HA (but surely more models are compatible than the ones listed here) https://community.home-assistant.io/t/working-usb-enclosures-and-adapters-with-hassos/212763
Edit: as for SSD, I went for Samsung EVO model
Sidenote: all SSD will be more reliable than a sd card because they are less sensitive to rewrite counts